L. Spicci, and M. Cati
Esaote SpA, Florence, Italy
The technology involved in high performance ultrasound imaging probes needs a reliable model to help in new projects development and performance simulations. To achieve a useful model, it is necessary to use correct values for all material parameters involved in the electro-acoustical performances of the piezoelectric material, but unfortunately some of these parameters are known only with high ...
S. Oukach, M. Elganaoui, B. Pateyron, and H. Hamdi
Laboratoire des Sciences des Procèdes Céramiques et de Traitements de Surface SPCTS, Limoges, France
Laboratoire de Mécanique des Fluides et Energétique LMFE, Marrakech, Morocco
The quality of coatings obtained by means of thermal spraying depends strongly on the mechanism of the interaction between the molten droplets and the surface to be covered. The aim of the present study is to simulate the impact of a droplet onto a substrate, in order to have a good understanding of the dynamics of droplets impact. In this study, the process of droplet spreading is described; ...
Université Paris-Est, CERTES, Créteil Cedex, France
In this paper, thermal properties of composites are investigated numerically and experimentally. In the numerical study, finite-elements method in COMSOL is used to modelize heat transfer and to calculate the Effective Thermal Conductivity (ETC) of the composite for three elementary cells, such as simple cubic (SC), body centered cubic (BCC) and face centered cubic (FCC). The effect of the ...
T. Bödrich, H. Neubert, and R. Disselnkötter
Technische Universität Dresden, Germany
ABB AG, Forschungszentrum Deutschland, Ladenburg, Germany
The operation of transformers is characterised by strong dynamic interactions between the magnetic system and the electric circuits that are connected to the primary and econdary windings. Transient finite element modelling (FEM) of the transformer with coupling to SPICE circuit models containing the electrical sources and loads is a powerful means for analysis and design. This paper describes ...
2D Axial-Symmetric Model For Fluid Flow And Heat Transfer In The Melting And Resolidification Of A Vertical Cylinder
S. Morville, M. Carin, M. Muller, M. Gharbi, P. Peyre, D. Carron, P. Le Masson, and R. Fabro
Laboratoire LIMATB, Université de Bretagne Sud, Lorient , France
Laboratoire PIMM, Arts et Métiers ParisTech, Paris, France
Laser direct deposition is a process, different from molding or machining, which allows the producing of fully densified and operational components. This technique involves injecting metal powder through a coaxial nozzle into a melt pool obtained by a moving laser beam. The final object is obtained by superimposing the layers created by the process. The roughness of the functional part is ...
Finite Element Modeling of Coupled Heat and Mass Transfer of a Single Maize Kernel Based on Water Potential Using COMSOL Multiphysics Simulation
A.J. Kovács, E. Lakatos, G. Milics, and M. Neményi
University of West Hungary, Institute of Biosystems Engineering, Mosonmagyarovar, Hungary
Finite element modeling of agricultural materials is very often used for describing physical processes. However, exact physical measurements are needed as input parameters for the models. Knowing the driving forces (potentials) during heat and mass transfers is necessary for an accurate model. Water potential gradients as the driving force are used in contrast with the conventional practice ...
S. Francois, and P. Namy
Nexans Research Center, Lyon cedex, France
SIMTEC, Grenoble, France
Power over Ethernet (PoE/PoE+) is a technology allowing to transmit data and power over the same data cable. The major concern for this technology is the degradation of data transmission performances due to the temperature increase in the cable. To have a better quantitative and qualitative knowledge of the temperature field in the cables, Nexans has developed a 2D finite element thermal model ...
M. Kavasoglu, R. Haettel, and C.H. Ploetner
ABB Corporate Research, Västerås, Sweden
ABB Transformers, Varennes, Canada
Transformers, as any other industrial products, have to comply with various requirements on noise levels. Three main sources of noise can be identified in transformers: no-load noise or core noise generated by magnetostriction in the core steel laminations, load noise produced by electromagnetic forces in the windings and noise due to auxiliary equipment such as fans and pumps used in the ...
A Finite Element Model For Structural And Aeroelastic Analysis Of Rotary Wings With Advanced Blade Geometry
E. Piccione, G. Bernardini, and M. Gennaretti
University Roma Tre Dept. of Mechanical and Industrial Engineering, Via della Vasca Navale, Rome, Italy
Objective of this paper is the development and implementation of a finite element model, in a COMSOL Multiphysics context, for the prediction of the aeroelastic behavior of rotor blades. In particular, the attention is focused on new generation blades characterized by curved elastic axes, with the presence of tip sweep and anhedral angles. The blade structural model implemented is based on ...
M. Beckmann-Kluge, F. Ferrero, V. Schröder, A. Acikalin, and J. Steinbach
Federal Institute for Materials Research and Testing, Technical University, Berlin, Germany
Tetrafluoroethylene (TFE) is a gas widely employed in industry, which can under specific circumstances experience an exothermic dimerization to octafluorocyclobutane. If the heat generated by this reaction cannot be dissipated to the surroundings, the temperature inside the reactor will continue rising, leading to conditions where TFE can decompose in tetrafluoromethane and carbon black. This ...