Product:Batteries & Fuel Cells Module
Product:Batteries & Fuel Cells Module
Simulate Battery and Fuel Cell Designs with the Batteries & Fuel Cells Module
Batteries and Fuel Cells: Greater Energy Densities, Longer Lifetimes
Batteries and fuel cells are being asked to perform in more challenging environments, with greater energy densities or power efficiencies, over longer lifetimes. These requirements are placing more pressure on these industries, and modeling and simulation is fast becoming one of the necessary tools for developing, designing, optimizing, and ensuring quality and safety of batteries and fuel cells during operation. Examples of systems that may be studied include lead-acid batteries, lithium-ion batteries, nickel metal-hydride batteries, solid oxide fuel cells (SOFCs), direct-methanol fuel cells (DMFCs), and proton exchange membrane fuel cells (PEMFCs).
The Batteries & Fuel Cells Module models the underlying electrochemical behavior in the electrodes and electrolytes of batteries and fuel cells. It allows you to investigate their performance for different operating conditions, design configurations, and deterioration due to different aging mechanisms. With this add-on module, you can simulate characteristics such as the transport of charged and neutral species, current conduction, fluid flow, heat transfer, and the nature and driving forces of electrochemical reactions at planar and in porous electrodes. Using this understanding of these characteristics, you can design and optimize the geometries and material choices of your system's electrodes, separators, membranes, electrolyte, and current collectors and feeders with respect to performance, thermal management, and safety.
Building Complexity Into Your Battery and Fuel Cell Models
If you're starting from scratch with your model of a new design, or even of a battery or fuel cell that has been deployed to your application, you should start off simple, and then add complexity to your modeling. Usually, this means investigating the characteristics of the device through a primary current distribution model. This simplifies the electrochemical reaction, electrolyte, and other components by describing it as conductors with resistances, utilizing Ohm's law. Primary current distribution models provide a lot of feedback about your device's geometry, and can be used to receive indications on its thermal management and even its structural integrity due to thermal expansions.
The Batteries & Fuel Cells Module contains specific interfaces within the COMSOL Desktop® graphical user interface (GUI) for a large number of physics formulations. Known as Physics interfaces, the Primary Current Distribution interface contains appropriate fields for specifying material properties, like the conductivity of electrodes and electrolyte, for all the different components in your battery or fuel cell design. Furthermore, it is easily coupled with the physics interfaces that describe other characteristics, such as Joule heating or the analysis of thermal stresses, that may exist within the Batteries & Fuel Cells Module, COMSOL Multiphysics, or one of the other physics-based modules.
Investigate the Electrochemical Characteristics of Your System
Increasing the complexity of your investigation, the kinetic characteristics of your electrochemical reactions are highly dependent on the microstructure of electrodes, electrocatalyst material, and composition of the electrolyte. There are very few material databases available that list electrochemical reaction kinetic parameters, so electrochemists run experiments to find these parameters specifically for their device. Yet, running detailed and controlled experiments within closed systems like batteries and fuel cells is difficult, particularly with the number of different physical parameters that can affect the electrochemical process. In order to receive accurate descriptions for these kinetic parameters, you often need to compare your experiments to models of the same experimental process, and then hone in on the actual values for these parameters. The Batteries & Fuel Cells Module has physics interfaces that simulate these experiments, such as cyclic voltammetry and electrochemical impedance spectroscopy (EIS or AC Impedance), and tools for importing data, plotting it, and even performing parameter estimations on it (requires the Optimization Module)
Once the electrochemical kinetics have been established, you can involve them in investigations of your batteries and fuel cells through secondary current distribution models. In these models, electrochemical reactions are directly affected by the charge transfer mechanism and the activation overpotentials. Such models give a better indication of the operating voltages and currents of your system and are useful in deciding electrode and electrocatalyst materials, while allowing you to include activation overpotential losses within any thermal study you may perform.
In addition, the Secondary Current Distribution interface can be fully coupled with the Chemical Species Transport interfaces that describe the transport of species in the gas pores, in gas diffusion electrodes (GDEs), for instance. In the description of GDEs, the transport of dissolved gases in the pore electrolyte and their transport to the active sites can be accounted for using agglomerate models or thin film models. The transport of gas in the pores is then also coupled to the transport and flow in the gas channel, for example in fuel cell bipolar plates.
Homogeneous reactions can be accounted for by using kinetic expressions in the Mass Transfer interface in the Batteries & Fuel Cells Module, where arbitrary sink and source terms can be defined. Alternatively, they can be defined in the physics interfaces in the Chemical Reaction Engineering Module and coupled to your battery or fuel cell model.
Receive a Full Picture of the Whole Process
Yet, the previous types of models assume that concentration is constant throughout the electrolyte, and that current transport only occurs through ionic migration, which is patently not true. One of the important factors driving an electrochemical reaction is the electrolyte composition in the vicinity of the reacting sites. To really investigate the electrochemical characteristics of a battery and fuel cell, a tertiary distribution study may be required. This takes into consideration the variation in concentration and should include a good description of the material balances and transport in the electrolyte.
Also for tertiary current distribution, the composition of the electrolyte and pore electrolyte may be fully coupled with the material balances in the gas phase and in the gas pores in porous electrodes and GDEs. These descriptions can also include the transport of species through the pore electrolyte using agglomerate and thin film models. In the case of batteries, specific intercalation equations are also incorporated, to account for the transport in electrode particles.
Materials in separators and electrodes may also react in homogeneous reactions, resulting in deterioration of performance. The Chemical Species Transport interfaces enable you to model the chemical reactions of these materials for estimating the effect of aging of the cell materials may have on battery and fuel cell performance.
The conduction of electric current in the electrodes and in the current collectors is described using Ohm's law, in combination with the equations for current conservation. This accounts for the resistive losses in electronic conductors, like current collectors and feeders, electrodes, porous electrodes, and GDEs. Current collectors and feeders can also be modeled using thin conductive layers, also called shells, in order to avoid meshing along the thickness of these thin layers. The current balances in the electronic conductors can be coupled to the current balances in the electrolyte and pore electrolyte through the charge transfer reactions using the dedicated electrode interfaces.
Integrate Battery and Fuel Cell Models with Other physics
Models developed in the Batteries and Fuel Cells Module may also be integrated with physics interfaces in any of the other modules in the COMSOL Product Suite. Via such integration, you may uncover critical information concerning the design and operation of current collectors and feeders, cooling systems, the optimization of electrodes, separators and membranes, and thermal management, with respect to performance and the deterioration of components due to aging.
Fluid Flow interfaces from the the CFD Module or the Heat Transfer Module, which support the simulation of turbulent flow, can be utilized in modeling the heating and cooling systems of lithium-ion batteries, or high temperature fuel cells, such as the MCFC and the SOFC. These may also require formulations for surface-to-surface radiation, which is supported by the Heat Transfer Module. Parameter estimation from electrochemical impedance spectroscopy (EIS or AC impedance spectroscopy), voltammetry, and current interruption simulations and experiments can be done in conjunction with the Optimization Module. One interesting coupling for modeling the aging of electrodes is the inclusion of the structural stresses induced by changes in density during charge and discharge in the electrodes. These stresses can be used to estimate the extent of micro-fractures in the electrode particles, which result in loss of electric conductivity that deteriorates the performance of the electrode.
Physics Interfaces for Simulating all Varieties of Electrochemical Behavior
The Batteries & Fuel Cells Module is the only simulation software that can be used freely for modeling all types of fuel cells and batteries, with the most robust features for simulating all varieties of electrochemical behavior. Contained within the product are a number of physics interfaces that simulate either the electrochemical processes themselves, or the surrounding processes that affect them.
Chemical Species Transport
The reacting species of batteries and fuel cells can exist and then be transferred to a variety of different states and phases. This includes existing as gases, liquids and solids, in concentrated and dilute electrolytes, mixtures and solid-state solutions. The Batteries & Fuel Cells Module interfaces for material transport model the transport of chemical species through a variety of both free and porous media. This includes the diffusion, convection, and migration in dilute and concentrated solutions and mixtures, in planar, porous electrodes, and GDEs.
Migration is an available term in all the physics interfaces, which is accounted for in the Tertiary Current Distribution interface by the Nernst-Planck Equations interface. Material transport is also described in physics interfaces for modeling lithium-ion batteries, lead-acid batteries, and binary electrolyte batteries, in ways specific to these electrolytes. A specific Reacting Flow interface is also available for modeling chemical species transport directly coupled to flow and chemical reactions.
Electrochemical Reaction Kinetics
As with all the modules in the COMSOL Product Suite, you can define any equation you like in the edit fields within the physics interfaces and have them be dependent on any of the variables within your modeled system. When this is done for electrochemical charge transfer reactions, the kinetics expressions can be arbitrary functions of the chemical species' concentrations, temperature, and the local electrode and electrolyte potentials at the electrode-electrolyte interface.
The Batteries & Fuel Cells Module provides predefined physics interfaces that help in the definitions of these kinetics. This includes the Electroanalysis interfaces, which are specifically useful for modeling applications like AC Impedance. In the Secondary and Tertiary Current Distribution interfaces, edit fields are available for the electrode kinetic parameters of equilibrium potential, anodic and cathodic charge transfer coefficients, exchange current density, the symmetry factor, and stoichiometry. Predefined expressions are also available for Butler-Volmer and Tafel expressions. In the Tertiary Current Distribution interface, the local concentration of the electroactive species is included in the reaction expressions by using the variables for the concentration. Porous electrodes and GDEs are also catered to in these physics interfaces, where the effective electrolyte and electrode conductivities can be specified along with anisotropic behavior.
Current Balances in the Electrolyte and Electrodes
The practical purpose of batteries and fuel cells is to facilitate the conversion of chemical energy to electrical energy, and vice versa (in the case of batteries). Losses in this conversion should be as small as possible and aging should also be kept to a minimum. To be used for design and optimization, simulations often have to include the effects of ion transport in the electrolyte, membranes and porous electrodes, and the electron conduction in the electrodes, all in combination with the conservation of current and charge.
The Primary and Secondary Current Distribution interfaces assume that ions move only through the effects of the electric field, neglecting diffusion, although they can still include approximative analytical expressions for concentration overpotential in porous electrodes. The Secondary Current density interface can also be fully coupled to gas phase transport, using the Maxwell-Stefan equations, in the pores in gas diffusion electrodes. This includes the diffusion of dissolved species in the pore electrolyte between the gas pore and the active sites, using agglomerate models or thin film models.
The Tertiary Current Distribution interface considers the transport of ions through the contributions from all three material transport processes: diffusion, convection, and migration through the Nernst-Planck equations. All these contributions are therefore included in the formulations that describe the current density, though convection is usually cancelled out by electroneutrality. This formulation is also coupled to the charge transfer reactions at the electrode-electrolyte interface, and provides you with results for cell voltage as it relates to the cell current for stationary, transient, and frequency domain (EIS) analyses.
The conduction of electric current in the electrodes and in the current collectors is described using Ohm's law in combination with the equations for current conservation, including electric conduction in porous electrodes and GDEs. An interface that simplifies the modeling of current conduction in thin current collectors and feeders, using thin layers (shells) without having to mesh them, is also included in the Batteries & Fuel Cells Module. Electronic conducting particles, fibers, or filaments can also be included inside a cell to simulate the effects of short circuiting and thermal runaway in batteries.
Specific physics interfaces have been included in the Batteries & Fuel Cells Module for modeling lithium-ion batteries. This includes extra terms and formulations to describe internal particle diffusion (intercalation) and the solid-electrolyte interface (SEI) as having a thickness and included as a model variable. The growth of the SEI during operation and under different operating conditions can be modeled to simulate aging. The Lead-Acid Battery interface is also provided, where it additionally considers porosity variation in the electrodes, due to the charging and discharging of the battery, and the average superficial velocity of the electrolyte caused by this change in porosity. Binary electrolyte batteries are best modeled within their specific physics interface, as it considers concentrated electrolytes and the constraints that electroneutrality places on the transport of ions in such systems, as well as the intercalation of species in the particles that form the porous electrodes. This physics interface is useful for modeling the nickel-metal hydride and the nickel-cadmium batteries.
Laminar and porous media fluid flow are accounted for in the Batteries & Fuel Cells Module in physics interfaces that solve the Navier-Stokes equations, Darcy's Law, and the Brinkman Equations. You can account for turbulent and two-phase flow by including Fluid Flow interfaces from the CFD Module in your simulations.
The Batteries & Fuel Cells Module features physics interfaces for modeling heat transfer through convection, conduction, and thermal diffusion due to the action of ionic migration. A specific interface for Joule heating that also includes the contributions of the activation losses is available along with one for modeling heat transfer through porous media. This takes into account the different conductivities in the solid and fluid phases, along with the convective thermal dispersion that occurs in this type of media. Surface-to-surface radiation can be accounted for in high temperature systems by coupling your models to physics interfaces in the Heat Transfer Module.
Batteries & Fuel Cells Module
- Primary, Secondary, and Tertiary Current Distribution interfaces for current balances in the electrolyte and pore electrolyte for free and porous media
- Formulations for electroneutrality, supporting electrolyte, or Poisson's equation for the charge balance equations
- Nernst-Planck equations in dilute and concentrated solutions
- Nernst-Einstein equation for relating mobility and diffusivity in electrolytes
- Maxwell-Stefan equation for transport in gases including homogeneous and electrochemical reactions as sources and sinks
- Ohm's law and conservation of current in the electrodes
- Nernst equation for equilibrium potential and concentration overpotential
- Stoichiometry and Faraday's law for automatic coupling of material and current balances to electrode reactions
- Electrode kinetics accounting for activation and concentration overpotential
- Electrocatalysis including adsorption and desorption
- Butler-Volmer and Tafel equations for predefined kinetics
- Solid electrolyte interface description (SEI) including a model variable for varying the interface thickness depending on operating conditions
- Intercalation of species in electrode particles
- Predefined formulations for porous electrodes and GDEs, including effects of porosity and tortuosity using Bruggeman relations for effective media
- Agglomerate models and thin film models for describing transport in pore electrolytes in porous electrode and GDEs
- Porosity variation due to dissolution of electrode material during operation by including porosity as a model variable coupled to the charge transfer reactions
- Electrochemical impedance spectroscopy (AC Impedance) studies for all described systems, including the influence of double layer capacitance
- Current interrupt studies
- Stationary and transient simulations with solvers settings adapted for electrochemical systems
- Joule heating due to ohmic losses and heating due to activation losses in the electrodes and in the electrolyte
- Heat transfer in free and porous media, including laminar nonisothermal flow
- Predefined coupling for flow in porous media in contact with open channels, such as in fuel cell bipolar plates and cooling channels, using the Brinkman equations
- Chemical species transport and reactions for simulation of aging due to chemical deterioration of battery materials, for example separators
- Design and operation studies of:
- Alkaline FC
- Direct Methanol FC
- Molten Carbonate FC
- Proton Exchange Membrane (PEM) FC
- Solid Oxide FC
- Fuel cell stacks
- Lead acid battery
- Lithium ion battery
- Nickel hydride battery
- Battery packs
- Current collectors and current feeders
- Porous electrodes
- Gas diffusion electrodes (GDEs)
- Solid Electrolytes
- Modeling and simulations of:
- Thermal management
- Thermal runaway in batteries
- Short circuits in batteries
- Aging mechanisms due to structural, thermal, and chemical effects
Highly Accurate Li-ion Battery Simulation
Mikael Cugnet French Atomic and Alternative Energy Commission
Battery management systems (BMSs) are designed to protect the batteries and predict their charge level. They use circuit models often derived from electrochemical impedance spectroscopy (EIS) measurements to construct an equivalent circuit model (ECM) that consists of resistors and capacitors connected both in series and in parallel. Yet, ECMs do ...
Battery Simulation Propels Electric Cars in China
Dr. Songrui Wang Tianjin Institute of Power Sources, Tianjin, China
Dr. Songrui Wang is a researcher at The Tianjin Institute of Power Sources, involved in battery testing and evaluation for design recommendations on safety. She analyzes the risk of potential fire hazards associated with lithium ion batteries, which are fast becoming the most popular sort of battery for vehicles, mobile devices, and many other ...
1D Lithium-Ion Battery Model for the Capacity Fade Tutorial
Side reactions and degradation processes may lead to a number of undesirable effects, causing capacity loss in lithium-ion batteries. Typically, aging occurs due to multiple complex phenomena and reactions that occur simultaneously at different places in the battery, and the degradation rate varies between certain stages during a load cycle, ...
Thermal Modeling of a Cylindrical Lithium-Ion Battery in 3D
This example simulates the heat profile in an air-cooled cylindrical battery in 3d. The battery is placed in a matrix in a battery pack. The thermal model is coupled to a 1d-battery model that is used to generate a heat source in the active battery material. The model requires the Batteries & Fuel Cells Module and the Heat Transfer Module
Cyclic Voltammetry at a Macroelectrode in 1D
Cyclic voltammetry is a common analytical technique for investigating electrochemical systems. In this method, the potential difference between a working electrode and a reference electrode is swept linearly in time from a start potential to a vertex potential, and back again. The current-voltage waveform, called a voltammogram, provides ...
Liquid-Cooled Lithium-Ion Battery Pack
This model simulates a temperature profile in a number of cells and cooling fins in a liquid-cooled battery pack. The model solves in 3D and for an operational point during a load cycle. A full 1D electrochemical model for the lithium battery calculates the average heat source.
Internal Short Circuit in a Lithium-Ion Battery
During an internal short circuit of a battery, the two electrode materials are internally and electronically interconnected, giving rise to high local current densities. Internal short circuits may occur in a lithium-ion battery due to, for instance, lithium dendrite formation or a compressive shock. A prolonged internal short circuit results in ...
Soluble Lead-Acid Redox Flow Battery
In a redox flow battery electrochemical energy is stored as redox couples in the electrolyte, which is stored in tanks outside the electrochemical cell. During operation, electrolyte is pumped through the cell and, due to the electrochemical reactions, the individual concentrations of the active species in the electrolyte are changed. The state ...
Electrochemical Impedance Spectroscopy
Electrochemical impedance spectroscopy (EIS) is a common technique in electroanalysis. It is used to study the harmonic response of an electrochemical system. A small, sinusoidal variation is applied to the potential at the working electrode, and the resulting current is analyzed in the frequency domain. The real and imaginary components of the ...
Modeling Impedance in the Lithium-Ion Battery
The impedance of a lithium-ion battery cell with a negative LTO and positive NCA electrode is modeled for harmonic perturbations between 10 mHz to 1000 Hz. The model incorporates an additional double-layer current at the conductive material in the positive electrode. The impedance of each electrode is also possible to investigate versus a ...
2D Lithium-Ion Battery
The following example is a 2D tutorial model of a lithium-ion battery. The cell geometry is not based on a real application; it is only meant to demonstrate a 2D model setup.
Current Density Distribution in a Solid Oxide Fuel Cell
This model presents a study of the current density distribution in a solid oxide fuel cell (SOFC). The model includes the full coupling between the mass balances at the anode and cathode, the momentum balances in the gas channels, the gas flow in the porous electrodes, the balance of the ionic current carried by the oxide ion, and a balance of ...
Every business and every simulation need is different. In order to fully evaluate whether or not the COMSOL Multiphysics® software will meet your requirements, you need to contact us. By talking to one of our sales representatives, you will get personalized recommendations and fully documented examples to help you get the most out of your evaluation and guide you to choose the best license option to suit your needs.
Just click on the "Contact COMSOL" button, fill in your contact details and any specific comments or questions, and submit. You will receive a response from a sales representative within one business day.