S. Sandoval Torres, A. de Lourdes Allier González, L.L. Méndez Lagunas
Instituto Politécnico Nacional, CIIDIR, Oaxaca, Mexico
In this work we solve a model to simulate the drying of potatoes slices. The model considers both the transport of free and vapor water by applying a mechanistic approach. The critical moisture point (CMP) was considered, since it is a transition zone and it represents the point where water saturation is near from cero and hygroscopic domain begins. The CMP divides the hygroscopic and ...
L.M. de Vries, A. Nardi, A.E. Idiart, P. Trinchero, J. Molinero, F. Vahlund, H. von Schenck
Amphos 21, Barcelona, Spain
Swedish Nuclear Fuel and Waste Management, Stockholm, Sweden
The Swedish Nuclear Fuel and Waste Management Co (SKB) is responsible for final disposal of spent fuel and radioactive waste. SKB operates SFR, an underground waste repository in crystalline rock. The evolution of groundwater flow within the repository needs to be estimated considering different options for the design of the engineered barriers. The goal is to predict the effects of flow and ...
P. S. Rao, C. K. Chandra
Agricultural and Food Engineering Department, Indian Institute of Technology Kharagpur, West Bengal, India
High Pressure Processing (HPP) is a leading non-thermal food processing technology that is often cited as a major technological innovation in food preservation. Although it is very early to place this emerging technology among the list of breakthroughs in food processing, HPP has started to become a viable commercial alternative for pasteurisation of value added fruits, vegetables, meat, and ...
X. Ma, M.B. de Rooij, and D.J. Schipper
Materials Innovation Institute, Enschede, The Netherlands
University of Twente, Enschede, The Netherlands
This paper describes the use of COMSOL Multiphysics® to determine the shear layer thickness in thin–section aluminum extrusion, based on the minimum work criterion. The studied two aluminum alloys are AA 6063 and AA 7020. The results show that a continuous shear layer featuring shear localization due to localized thermal softening is not possible to form under typical thin–section ...
Equation-Based Modelling: True Large Strain, Large Displacement and Anand's Plasticity Model with COMSOL's Moving Mesh Application Mode
O. Toscanelli, V. Colla, and M. Vannucci
Scuola Superiore S. Anna, Pontedera, PI, Italy
In this work the solution of the structural problem obtained by mean of the velocity approach is presented. More in detail the balance and constitutive equations are expressed in Eulerian form, the mesh is not material. The approach is general, is suitable both for material boundary or no-material boundary and for a generic material model. The Hooke's elastic model and the Anand's plasticity ...
N. Martaj, P. Rochelle, L. Grosu, R. Bennacer, and S. Savarese
Universitè de Paris, Paris, France
Institut Jean Le Rond d'Alembert, Université Paris 6
Laboratoire LEEVAM «Environnement, Energétique, Valorisation, Matériaux», Universitéde Cergy-Pontoise
COMSOL France, 5 pl. R Schuman, 38000 Grenoble
The alternative engines of Stirling type, are engines running on "hot air", using both an external heat source and regeneration. They should be considered as an alternative for the effective conversion of renewable energy sources into work, with their theoretical yield equal to the theoretical Carnot limit. The output efficiency and the power of these engines are strongly related to the ...
Upper Austria University of Applied Sciences
This presentation deals with how COMSOL Multiphysics can be used in education. The presentation is performed by demonstrating various multiphysics examples, their setup, modeling approach, and solution. ------------------------------------------- Keynote speaker's biography: Dr. Mario Jungwirth has been a professor at the Upper Austria University of Applied Sciences since 2003. In 2001, he ...
NanoScience Simulation Laboratory, Department of Physics, Fu Jen Catholic University, Taipei County, Taiwan
The Child-Langmuir law gives the maximum electron current, known as the space-charge-limited current, which arises because the space charge in the diode presents a potential barrier to the incident electrons. While there are modifications due to geometrical and relativistic effects, the limited current remains a fundamental quantity characterizing the beam-gap interaction. In the research of ...
L. Wissmeier, and D. A.Barry
GIT HydroS Consult GmbH, Freiburg, Germany
EPFL, Lausanne, Switzerland
We present a software tool for simulations of subsurface flow and solute transport in combination with comprehensive intra-phase and inter-phase geochemistry. The software uses PHREEQC as a reaction engine to COMSOL Multiphysics®. The coupling with PHREEQC gives major advantages over COMSOL’s built-in reaction capabilities, i.e., the soil solution is speciated from its element composition ...
O. Toscanelli, and V. Colla
Scuola Superiore S. Anna
The flux of a fluid in permeable media can be modelled using a continuous. To link the real system with the continuous model is mandatory to realize a suitable average of the equations and of the variables. The dispersion term comes from this averaging but it is not only a mathematical product of the modelling. The dispersion is due to the intrinsic geometry of the permeable media that forces ...