Mitsubishi Turbocharger & Engine Europe, Almere, The Netherlands
This study presents a rotordynamic analysis of a rotor on hydrodynamic bearings using COMSOL Multiphysics®. In this paper, the complexity of the model is gradually increased. Starting point of the analysis is the modal analysis of the rotor in free-free conditions. A Reynolds model is set up to predict the film pressure distribution under shaft loading. Due to the cross coupling terms of the ...
Lamb Waves and Dispersion Curves in Plates and It’s Applications in NDE Experiences Using Comsol Multiphysics
P. Gómez, J. P. Fernandez, and P. D. García
Hydro-Geophysics & NDE Modeling Unit
University of Oviedo
In this paper, a model for numerically obtaining lamb wave modes and dispersion curves in plates is presented. It is shown that COMSOL Multiphysics can be employed to simulate the behavior of guided waves in dispersive plates, which is useful for NDE applications. A two dimensional steel plate (4x0.1 meters) is excited with a space-time impact point source. To model the point source, we use ...
J. Soons[1,2], C. Steele, S. Puria
Lab of Biomedical physics, University of Antwerp, Antwerp, Belgium
Department of Mechanical Engineering, Stanford University, Stanford, USA
Sound vibrations are collected from the external environment by the eardrum and are guided to the basilar membrane in the cochlea. Pressure differences in the two scalae of the cochlea result in a traveling wave on the basilar membrane. The tiny displacements are detected by the deflection of thousands of hair cells, situated along this membrane. It is hypothesized that some 3/4 of these hair ...
Esaote SpA, Florence, Italy
Pulse-echo FEM simulation is seldom found in literature for ultrasound imaging array probes, since the complete modeling of such device is extremely complicated. Nevertheless, the 2D FEM described in the present work was successful, thanks to the following design procedure (see figure): Two piezoacoustic models were employed, one for transmission of the pressure wave into the acoustic domain, ...
B. Goldsberry, M. Isakson
Applied Research Laboratories, The University of Texas at Austin, Austin, TX, USA
Measuring geoacoustic parameters of underwater sediments is important for accurate modeling of underwater acoustic propagation. While the density and compressional wave speeds can be directly measured in sediments, shear wave speeds are difficult to measure because they are highly attenuated. However, shear wave speeds can be indirectly determined through measurement of Scholte interface wave ...
C. Van der Woude, and S. Narasimhan
University of Waterloo, Waterloo, ON, Canada
This paper presents a study of a wind turbine subjected to wind and seismic loading, carried out using COMSOL Multiphysics. The dynamic properties and response of wind turbine structures are of interest, as recent developments in wind energy have led to the design and construction of increasingly large and flexible turbine structures. A typical turbine structure model was created in ...
G. McRobbie, P. Marin-Franch, and S. Cochrane
 University of Paisley
 Piezo Composite Transducers, Ltd
This paper illustrates how finite element analysis with COMSOL Multiphysics can be used to simulate the mechanical and electrical characteristics of piezoelectric transducers. It also shows how beam transmit plots and performance measurements can be modeled by coupling between a piezo domain and a second domain governed by the wave equation.
A. Cavuto, G.M. Revel , M. Martarelli , F. Sopranzetti 
Università Politecnica delle Marche, Ancona, Italy
Università e-Campus, Novedrate (CO), Italy
A 2D axisymmetric model was considered in order to evaluate the propagation paths of the ultrasonic waves generated inside an aluminum plate sample due to a rapid thermal expansion produced by laser pulse. Laser Doppler Vibrometer is used to experimentally validate the numerical results of the wave propagation in the material. The presented numerical model is able to identify directivity patterns ...
Rakesh Kumar Pati , SK Mohammed ali, Sakuntala Mahapatra, Millee Panigrahi
MEMS Design Centre, Dept. of ETC, Trident Academy of Technology, Bhubaneswar, Odisha, India
Despite of the existing successful clinical applications, however, the interaction, i.e. artificial sensing, between the robot and the patient is still very limited. With the help of various cameras, vision is almost the only feeling that a robot can have. In order to imitate the human skin, various signals e.g., the strength of pressure, change of strength, speed and acceleration should be ...
Dinex Emission Technology A/S, Middelfart, Denmark
Exhaust noise must meet legislation targets, customer expectations and cost reduction which call for design optimization of the exhaust systems in the design phase. One solution is to use 3 dimensional linear pressure acoustics and calculate the transfer matrix of the muffler. The transfer matrix is the basis for calculating either the insertion loss or transmission loss of a muffler. The 3D ...