K. C. Koppenhoefer, J. Thomas, J. S. Crompton
AltaSim Technologies, LLC., Columbus, OH, USA
Computational tools based on the finite element method have been used extensively to develop solutions for elastic and elastic-plastic fracture mechanics problems. This work uses a small-scale yielding model to compare results developed from COMSOL Multiphysics® with another finite element modeling package and analytical solutions. Analysis are conducted for elastic, and elastic-plastic ...
P. L. Mills , K. Barman , S. Mothupally , A. Sonejee ,
 Texas A&M University - Kingsville, Kingsville, TX, USA
Introduction Fluid flow patterns in research or process-scale equipment where a fluid is contained between concentric rotating cylinders in the absence of bulk axial flow has received notable attention in the field of fluid mechanics. Annular flows occur in many practical applications, such as in the production of oil and gas, fluid viscometers, centrifugally-driven separation processes, ...
TEL US Holdings, Inc., Albany, NY, USA
Recently, the advanced plasma tools have been using very high frequency power sources (>100 MHz) and their combination to excite plasma utilized in semiconductor technology. This approach is evoking the regimes that are less understood and currently a subject to many studies and experimental investigations. The paper describes quasi-stochastic approach applied for sheath properties and ...
K. Al-Shurman, H. Naseem
The Institute for Nanoscience & Engineering, University of Arkansas, Fayetteville, AR, USA
Department of Electrical Engineering, University of Arkansas, Fayetteville, AR, USA
Chemical vapor deposition is considered a promising method for synthesis of graphene films on different types of substrate utilizing transition metals such as Ni. However, synthesizing a single-layer graphene and controlling the quality of the graphene CVD film on Ni are very challenging due to the multiplicity of the CVD growth conditions. COMSOL Multiphysics® software is used to investigate ...
University of Manchester, Manchester, UK
This report mainly discusses the implementation and results of a project proposal, “Modelling using Finite Element Methods”. The report is devoted to implementation, which is a model of an electromagnet. The software tool that is used to model the electromagnet is COMSOL Multiphysics®, a commercial FEA package provided by the University of Manchester, Computer Science School. Additionally, the ...
N. Huc 
 COMSOL France, Grenoble, France
This session is devoted to phase change modeling in heat transfer simulations. The great interest in phase change comes from the outstanding thermal performance that it enables in particular for cooling or thermal protection applications. Alternatively, phase change can induce most of the energy cost in drying or cooking applications. In all of these cases, a thermal analysis is required to ...
Comparison Between Phase Field and ALE Methods to Model the Keyhole Digging During Spot Laser Welding
V. Bruyere, C. Touvrey, P. Namy
CEA-DAM, Is-sur-Tille, France
SIMTEC, Grenoble, France
Nowadays, spot laser welding is a full-fledged part of industrial manufacturing and is routinely used due to its advantages. It generates very located temperature gradients, and therefore, induces small distortions in the pieces. The COMSOL Multiphysics® software is used to model the interaction stage of an isolated impact made with a Nd:YAG pulsed laser. The free surface evolution has been ...
S. Gorelick, M. Leivo, U. Kantojärvi
VTT Technical Research Centre of Finland, Espoo, Finland
Excessive air damping can be detrimental to the performance of oscillating MEMS components. Complex systems, such as structures in pre-etched cavities or angular comb-drive scanning mirrors, typically require simulations to reliably evaluate the air damping. The simulated and experimental performance of the following systems was evaluated and compared: two types of out-of-plane cantilevers, in ...
A Practical Method to Model Complex Three-Dimensional Geometries with Non-Uniform Material Properties Using Image-based Design and COMSOL Multiphysics®
J. Cepeda, S. Birla, J. Subbiah, H. Thippareddi
Department of Food Science & Technology, University of Nebraska, Lincoln, NE, USA
Department of Biological Systems Engineering, University of Nebraska, Lincoln, NE, USA
Geometries with heterogeneous material properties are typically defined as a set of multiple parts, each part representing a different material. However, assembling or defining the individual parts of complex geometries can be difficult. A practical method based on image-based mesh generation, a custom algorithm for labeling materials, and interpolation functions of COMSOL Multiphysics® can be ...
R. Jia, J. Hu, X. Xiong
Department of Mechanical Engineering, University of Bridgeport, Bridgeport, CT, USA
Department of Electrical and Computer Engineering, University of Bridgeport, Bridgeport, CT, USA
Plate fin heat exchangers are widely used for heat recovery or cooling purposes in many industries, such as cryogenics, aerospace and automobile industries. This paper developed a numerical model to simulate the heat transfer and fluid flow in a counter flow plate fin heat exchanger and optimize its design parameters. The conjugate heat transfer in the finned plate and fluids in the channels ...