M. Dimaki, J. Moresco Lange, P. Vazquez, P. Shah, F. Okkels, and W. Svendsen
Department of Micro- and Nanotechnology, Technical University of Denmark, Lyngby, Denmark
The need for fast, easy and cost-effective analysis of blood samples as well as our understanding of the functionality of cells and neurons are two rather pressing issues in the modern world. Both of these can be addressed by functional lab-on-a-chip systems, which have been designed and optimized for specific analyses. This paper deals with the design of several different systems for cell ...
Simulation of Optical Properties of the Si/SiO2/Al Interface at the Rear of Industrially Fabricated Si Solar Cells
Y. Yang, and P. Altermatt[1,2]
Institute for Solar Energy Research Hamelin (ISFH), Emmerthal, Germany
Dep. Solar Energy Research, Inst. Solid-State Physics, Leibniz University of Hanover, Germany
The specular and diffuse reflection properties of sunlight at the rear surface of silicon solar cells with various degrees of roughness are computed by solving the Maxwell and material equations in two dimensions, using the COMSOL RF Module. The model is tested on planar Si/SiO2/air interfaces and planar Si/SiO2/Al interfaces. The simulations show that for wavelengths of 800 nm, (i) maximum ...
J. Jeong, and H. Ramezani
Ecole Speciale des Travaux Publics du Batiment et del’Industrie(ESTP), Cachan, France
Ecole Polytechnique de l’Universite d’Orleans CNRS/CRMD, Orleans, France
The Cosserat models fall into the group of the extended continuum media. They are capable of treating the size effects (characteristic length) in a natural manner using six material moduli for the isotropic elastic cases instead of two (and) for the classical continuum mechanics. This model involves two constitutive laws corresponding to two kinds of balance equation. The first one handles the ...
C. Gavrila, A. Ghiaus, and I. Gruia
Technical University of Civil Engineering Bucharest, Faculty of Building Services, Bucharest, Romania
University of Bucharest, Faculty of Physics, Bucharest, Romania
A dynamic mathematical model, based on physical and transport properties and mass and energy balances, was developed for the simulation of unsteady convective drying of agricultural products (fruits and vegetables) in static bed conditions. The model utilizes water sorption isotherm equations and the change in solid density due to the shrinkage phenomenon. The aim of this article is to describe ...
M. Darif, and N. Semmar
GREMI-UMR6606, CNRS-Universite d’Orleans, Orléans, France
A 2D transient heat conduction model was created in COMSOL Multiphysics to simulate temperature changes in material irradiated by a KrF laser beam confined on silicon’s surface. In this paper, the obtained results are shown and discussed in case of bulk Silicon. The heat source is distributed in time with ‘gate’ and ‘gaussian’ shapes. The thermal properties values ...
H. Lorenzen, J. Timmerberg, and S. Mylvaganam
Department of Electrical Engineering, UAS OOW, Wilhelmshaven, Germany
Department Technology/Engineering, Telemark University College, Porsgrunn, Norway
Efforts involving simulation of transmission line networks necessitate the accurate values of the parameters of the lines. In this paper, as an attempt in estimating such parameters, the parameters of high voltage asymmetric power lines are calculated. In the process of estimation, the three phase equivalent circuit model is used. The resistance and inductance of such lines are dependent on ...
Dinex Emission Technology A/S, Middelfart, Denmark
Exhaust noise must meet legislation targets, customer expectations and cost reduction which call for design optimization of the exhaust systems in the design phase. One solution is to use 3 dimensional linear pressure acoustics and calculate the transfer matrix of the muffler. The transfer matrix is the basis for calculating either the insertion loss or transmission loss of a muffler. The 3D ...
Multiphysics Simulation of Thermoelectric Systems - Modeling of Peltier-Cooling and Thermoelectric Generation
Fraunhofer-Institute for Physical Measurement-Techniques (IPM), Freiburg, Germany
Electro-thermal interaction is commonly considered only as a matter of joule heating. In addition, the Seebeck-, Peltier- and Thompson-Effects are significant in materials with high thermoelectric figure of merit Z. These thermoelectric materials have a high Seebeck-coefficient α, a good electric conductivity σ, and a poor thermal conductivity λ. They have widespread areas of ...
Simulation of Production Processes using the Multiphysics Approach: The Electrochemical Machining Process
R. van Tijum
Advanced Technology Center, Philips Consumer Lifestyle, Drachten, The Netherlands
Redmer van Tijum studied Applied Physics at the University of Groningen. In 2006, he received his PhD title on ‘Interface and surface roughness of polymer metal laminates’ in the field of Material Science at the University of Groningen. After that he became research and development engineer at Philips, where he focussed his attention on the improvement of production processes mainly ...
Advanced Modeling of Friction Stir Welding – Improved Material Model for Aluminum Alloys and Modeling of Different Materials with Different Properties by Using the Level Set Method
Wilhelm Gronbach GmbH, Wasserburg a. Inn, Germany
Friction Stir Welding (FSW) has gained much importance throughout the last years. Beside comprehensive experimental work that has been carried out, the simulation of the welding zone is of major interest. Due to the high strains observed within the welding zone, the Eulerian (CFD) approach seems to be the most promising for the prediction of flow around the FSW tool. However, the CFD ...